Works with the AI Agents you already use

    Claude CodeClaude CodeCursorCursorCodex CLICodex CLIDeepSeekDeepSeekMuseMuse+22 more

    pcb design master

    0

    Principal-level hardware engineering skill for PCB layout audits, signal integrity, and high-speed circuit design.

    $15

    Secure checkout via Stripe

    Money-back guarantee

    Converts to your local currency at checkout

    Security scanned
    pcb design master

    pcb design master

    Example session with this skill installed

    I have a 4-layer board with a 12V to 3.3V 5A Buck converter. The output ripple is higher than expected. Review my SMPS layout strategy and check the PDN impedance.

    • Read your context and instructions
    • Compiled the pcb design master

    I have reviewed your 4-layer SMPS layout and Power Distribution Network. The primary issue is the placement of the input capacitors and the high-side MOSFET switching loop.

    Power Integrity & SMPS Audit Report

    CategoryFindingSeverity
    Hot-Loop GeometryThe input decoupling caps (C1, C2) are on the bottom layer, connected via 4 vias. This adds ~2.4nH of parasitic inductance, causing $V = L \cdot di/dt$ ringing at the SW node.[CRITICAL - SPIN REQUIRED]
    PDN ImpedanceTarget impedance $Z_{target}$ is 33m$\Omega$. Current MLCC selection (10uF 0603 X5R) suffers 65% capacitance loss at 12V DC bias. Effective capacitance is only 3.5uF.[HIGH - SI FAILURE RISK]
    Thermal RiseThe 3.3V 5A output trace is 20 mils wide on 1oz copper. IPC-2152 predicts a $\Delta T$ of $42^\circ\text{C}$, exceeding the $20^\circ\text{C}$ design limit.[MEDIUM - RELIABILITY]
    Gate DriveMissing $R_{boot}$ resistor (series with C3). High $dv/dt$ on the SW node is likely causing CGS Miller-effect turn-on, increasing switching losses.[MEDIUM - PERFORMANCE]

    Next steps

    1. Move input capacitors (C1, C2) to the top layer immediately adjacent to the Vin and PGND pins of the IC to eliminate vias in the hot-loop.
    2. Replace 0603 X5R decoupling caps with 1206 X7R rated for 25V to recover effective capacitance.
    3. Increase the 3.3V output polygon width to at least 85 mils or utilize a dedicated internal power plane on L3.
    4. Add a 2.2$\Omega$ resistor in series with the bootstrap capacitor to damp the gate drive.

    Connects securely to your tools. The creator never sees your data.

    About this skill

    Designing hardware at high frequencies or high power is a minefield of parasitic inductance and signal integrity failures. This skill acts as a Principal Hardware Architect to audit every trace, via, and component choice against Maxwell's equations and IPC standards.

    What it does

    • Physics-based auditing analyzes schematics and layouts using transmission-line theory, semiconductor physics, and thermodynamics.
    • Power integrity modeling calculates PDN target impedance and eliminates parallel anti-resonance in decoupling networks.
    • High-speed SI analysis manages differential pair skew, phase-velocity mismatch, and fiber-weave effects for multi-gigabit signals.
    • SMPS optimization reviews switching regulator hot-loops, snubber values, and Kelvin sense routing to minimize EMI.
    • Automated KiCad verification runs structural audits on .kicad_pcb files for DRC, DFM, and signal integrity compliance.

    How it works

    1. Analyze schematics for component derating, DC-bias capacitance loss in MLCCs, and thermal safety margins.
    2. Define stackup electromagnetics by calculating critical lengths based on driver slew rates and material prepreg styles.
    3. Audit PCB layout using the 8-Gate Engineering Review sequence from return paths to manufacturing yield.
    4. Run quantitative scripts to compute exact trace widths, via parasitics, and impedance matching for RF or differential pairs.

    Frameworks & tools

    Specifically designed for hardware engineers using KiCad, Altium, or Allegro workflows, with deep knowledge of IPC-2152, IEC 62368-1 safety, and CISPR EMC standards.

    Why this beats prompting it yourself

    Generic AI lacks the hardware-specific rigor to catch DC-bias capacitance drop or parasitic via inductance. This skill enforces a strict 8-Gate review protocol that quantifies physical mechanisms like skin depth and Seebeck offsets, preventing expensive board re-spins.

    Use cases

    • Audit a high-speed DDR4 or USB-C layout for impedance discontinuities and skew.
    • Verify 230V AC mains safety distances and creepage/clearance compliance.
    • Size power distribution networks for low-voltage, high-current FPGA rails.
    • Debug EMI failures by identifying common-mode radiation paths and loop areas.

    Known limitations

    Does not perform 3D full-wave EM simulation or SPICE netlist simulation. Requires manual input of specific vendor dielectric constants and silicon slew rates for maximum accuracy.

    Find more skills like this on the Claude Skills Marketplace, the Codex Skills Marketplace and the Gemini Skills Marketplace, or browse Claude Skills for Agents & Orchestration.

    Does not perform 3D EM simulation or SPICE transient analysis. Requires manual entry of vendor dielectric constants and driver slew rates for precise calculations.

    How to use

    1. 1

      Connect your agent to the Agensi MCP

      Copy the prompt and paste it into Claude, ChatGPT, Cursor or any agent that supports MCP. It sets up the connection for you. Manual setup

    2. 2

      Sign in to Agensi

      Your agent shows a sign-in link. Sign in and click Allow.

    3. 3

      Ask for what you need

      Your agent loads this skill and uses it on your task. It always asks before buying a skill.

    Reviews

    No reviews yet

    Be one of the first to try it. Every listed skill goes through the trust checks below.

    Security scanned

    Checked by our 8-point scan before listing

    Fresh listing

    Recently published to Agensi

    Money-back guarantee

    Doesn't do what its page promises? You get your money back.

    Trust & safety

    Security scan

    Security scan passed 11 days ago

    Software
    KiCad, freeroutingGit

    Permissions

    Terminal / Shell
    Write Files
    Read Files
    Browser
    Listed11 days ago

    What's inside

    Frequently Asked Questions

    This skill specializes in advanced physics-based auditing, identifying critical hardware risks like DC-bias capacitance loss, parasitic via inductance, and signal integrity failures that standard DRC tools often miss.

    The skill is optimized for high-speed and power-dense designs, including DDR4 memory routing, multi-gigabit differential pairs (USB-C/PCIe), and high-current FPGA power distribution networks.

    While it has specialized automation for KiCad (.kicad_pcb) files, you can use it with Altium, Allegro, or Mentor Graphics by providing netlists, stackup specifications, and layout screenshots for manual review.

    You receive the full PCB Design Master skill package, including the 8-Gate Engineering Review protocol and specialized quantitative scripts for calculating impedance and thermal safety margins.

    The agent is updated periodically to reflect the latest IPC standards (like IPC-2152) and emerging hardware safety regulations such as IEC 62368-1.

    No, it focuses on architectural auditing and quantitative calculations; you will still need to provide specific dielectric constants from your fabrication house and driver slew rates for the most accurate SI analysis.

    New in Agents & Orchestration