Works with the AI Agents you already use

    Claude CodeClaude CodeCursorCursorCodex CLICodex CLIDeepSeekDeepSeekMuseMuse+22 more

    Bill of Materials (BOM) Cost-Down Optimizer

    1

    Identify cost-saving hardware components and mitigate supply chain risks in your Bill of Materials.

    $4.99

    Secure checkout via Stripe

    Money-back guarantee

    Converts to your local currency at checkout

    Security scanned
    Bill of Materials (BOM) Cost-Down Optimizer

    Bill of Materials (BOM) Cost-Down Optimizer

    Example session with this skill installed

    Original BOM: MCU: STM32F405RGT6 ($8.50), IMU: MPU-6000 ($4.00), Motor Drivers: DRV8302 ($5.20), Enclosure: CNC Machined 6061 Aluminum ($12.00).

    Target Cost Reduction: 30% -

    Core Requirements: Must support betaflight firmware, needs to withstand moderate crashes, 6-axis motion tracking is mandatory.

    • Read your context and instructions
    • Compiled the bill of materials

    📉 BOM Optimization Summary

    Your BOM totals

    $29.70. A 30% reduction means a target of about

    $20.80, or roughly

    $8.90 saved. The enclosure is the biggest cost driver at $12.00 (40% of the BOM), followed by the STM32F405 ($8.50) and the DRV8302 ($5.20). The MPU-6000 is cheap but has a lifecycle problem rather than a cost problem.

    The target is reachable without touching the MCU. Moving the enclosure to molded or printed nylon saves $7 to $9.50, and the IMU swap saves $1.20 to $1.80. Resolving the motor driver issue saves another $3 to $4.60. Combined, these cut roughly 50% and clear the 30% goal with margin. An MCU swap can add $4 to $5 more, but it carries the most firmware risk, so I'd treat it as optional.

    Assumptions: prices below are my estimates at typical volume (1k+ units), not live quotes, so verify them on DigiKey, Mouser or LCSC. I've also assumed the $5.20 is the line total for all motor drivers.

    🔄 Alternative Component Recommendations

    Original Part/MaterialCurrent Issue (Cost/Volatility)Suggested Alternative 1 (Est. Savings)Suggested Alternative 2 (Est. Savings)Trade-offs / Impact
    CNC 6061 Aluminum enclosure ($12.00)Machining time dominates the cost, and aluminum pricing and tariffs swingInjection-molded PA6-GF30 (glass-filled nylon) at ~$2.50 (save ~$9.50). Needs tooling of roughly $5k to $15k, so it pays off at a few thousand unitsMJF/SLS 3D-printed PA12 at ~$5.00 (save ~$7.00). No tooling, good for low volumeExcellent crash toughness, since glass-filled nylon absorbs impact better than aluminum, which tends to bend or crack mounts. You lose heat spreading, so use thermal pads to a small heatsink if the driver stage runs hot. It is also lighter.
    MPU-6000 IMU ($4.00)Obsolete/NRND at TDK, with a real counterfeit risk on the broker marketICM-42688-P at ~$2.80 (save ~$1.20)BMI270 at ~$2.20 (save ~$1.80)Both are 6-axis and supported in Betaflight, and the ICM-42688-P has lower gyro noise than the MPU-6000, giving cleaner filtering. The BMI270 is slightly noisier and sensitive to mounting and vibration. Both need an SPI driver check and a PCB footprint change (LGA 2.5×3 mm).
    DRV8302 motor driver ($5.20)This is a gate driver for external MOSFETs, not an integrated ESC solution. It adds FET, sense and passive cost, and it is a poor fit for Betaflight's DShot-to-ESC modelFD6288Q 3-phase gate driver per motor channel, ~$1.20 for the set (save ~$4.00)TI DRV8300 at ~$2.00 (save ~$3.20). Pin-compatible in spirit with a simpler architecture, and more reliably sourced from a major vendorNeither has the DRV8302's built-in current-sense amps or buck regulator, so add a shunt and an op-amp (or use a sensorless AM32/BLHeli_32-class ESC MCU) plus a separate 5V/3.3V regulator. See the note below on whether to drop on-board drivers entirely.
    STM32F405RGT6 MCU ($8.50) (optional)Highest unit cost among the silicon, with price swings since the 2021–23 shortageArtery AT32F435RGT7 at ~$4.00 (save ~$4.50). Betaflight has target support for it, with a faster core and more flashSTM32F411CEU6 at ~$3.20 (save ~$5.30). Also a Betaflight targetThe AT32F435 needs a custom or existing unified target config, so confirm the exact variant in the current Betaflight release. The F411 has less flash, fewer UARTs and timers, and less CPU headroom for high loop rates with RPM filtering. Keep the F405 if you want zero firmware risk.

    Important design question on the DRV8302: Betaflight does not drive motor gates directly. The flight controller outputs DShot signals to ESCs, which run their own firmware (BLHeli_S, Bluejay, AM32 and similar). If this is a flight-controller-only board, the DRV8302 shouldn't be on it at all. Removing it and using an off-board 4-in-1 ESC saves the

    full $5.20. If you really are building an integrated FC+ESC, you need a dedicated ESC MCU per the options above, which adds a bit of BOM.

    Example combinations:

    Conservative (keep F405): PA12 MJF enclosure ($5.00) + ICM-42688-P ($2.80) + F405 ($8.50) + FD6288Q set ($1.20) =

    $17.50, about 41% savings

    Aggressive: PA6-GF30 molded ($2.50) + BMI270 ($2.20) + AT32F435 ($4.00) + FD6288Q set ($1.20) =

    $9.90, about 67% savings

    ⚠️ Supply Chain Risk Alert

    MPU-6000: This is the most urgent issue. It is obsolete or near end of life, and supply on the open market is full of remarked and counterfeit parts. The design-around is the ICM-42688-P or BMI270, and a footprint that accepts both makes you resilient to future shortages.

    STM32F405RGT6: Availability has recovered since the shortage years, but pricing still moves with allocation. Designing the PCB so an F405 and an AT32F435 can share a footprint (both LQFP64, with pin-mapping differences to check) gives you a second source.

    DRV8302: Moderate availability, with some lead-time exposure. A simpler gate driver such as the FD6288Q or DRV8300 reduces both cost and dependency.

    6061 aluminum enclosure: Exposed to metal price and tariff volatility, as well as CNC shop capacity. Moving to plastic removes that exposure.

    🎯 Next Steps for Engineering

    Validate the IMU swap first: build a small test board or breakout with the ICM-42688-P and BMI270, flash a current Betaflight build, and compare gyro noise, filter settings and flight tuning against the MPU-6000 baseline.
    2.

    Decide the ESC architecture: confirm whether the DRV8302 is meant to live on this board. If not, remove it and the power stage from the schematic. If it is, redesign around an ESC MCU plus FD6288Q or DRV8300, and add current sensing and regulation.
    3.

    PCB/CAD changes: update the IMU footprint (LGA) and SPI routing, and, if switching MCUs, pin-map the AT32F435 or F411 and check the target definition against Betaflight's unified-target repository. Redesign the enclosure for molding (draft angles, ribs, wall thickness) and add vibration-damping standoffs to protect the IMU.
    4.

    Run a crash and thermal test: drop-test and vibration-test the PA12 prototype enclosure, and check driver and MCU temperatures in a closed case.
    5.

    Sourcing: get live quotes from authorized distributors for all alternatives, request injection-molding quotes at your target volumes to confirm tooling payback, and qualify two sources per critical IC.

    Connects securely to your tools. The creator never sees your data.

    About this skill

    Hardware margins are crushed by over-specced components and supply chain volatility. This skill analyzes your Bill of Materials to find cheaper, functional alternatives and mitigate sourcing risks.

    What it does

    • Component Auditing reviews every line item to find over-specced, overpriced, or constrained parts.
    • Alternative Sourcing identifies at least two viable, lower-cost components or materials for every high-cost item.
    • Trade-off Mapping evaluates functional, thermal, and footprint impacts for every suggested change.
    • Risk Mitigation flags parts prone to global shortages and provides design-around strategies.

    How it works

    1. Input Data Provide your current BOM, target cost reduction percentage, and non-negotiable core requirements.
    2. Analysis Mode The agent scans for premium microcontrollers, sensors, or materials that can be swapped for more available or cheaper equivalents.
    3. Review Output Receive a structured table of alternatives and an executive summary of potential savings.

    Frameworks & tools

    This skill is designed for hardware engineering and supply chain workflows. It works with standard CSV or Markdown BOM exports from ECAD tools like Altium, KiCad, or Eagle.

    Why this beats prompting it yourself

    Generic LLM prompts often suggest components that are out of stock or ignore footprint and thermal constraints. This skill specifically enforces a trade-off evaluation and requires two alternatives per part, ensuring you have a fallback for every cost-saving measure.

    Use cases

    • Prototyping to Production Scaling a build where small per-unit savings represent significant total profit.
    • Supply Chain Pivot Finding drop-in replacements for components with 52-week lead times.
    • Cost Reduction Sprints Meeting aggressive "cost-down" targets without redesigning the entire system architecture.

    Known limitations

    This skill does not perform real-time API inventory checks and relies on historical training data for pricing. It cannot verify physical fit or signal integrity, which requires manual engineering validation.

    Find more skills like this on the Claude Skills Marketplace, the Codex Skills Marketplace and the Gemini Skills Marketplace, or browse Claude Skills for Business & Operations.

    Does not perform real-time inventory API calls. Requires manual validation for physical footprint compatibility and signal integrity.

    How to use

    1. 1

      Connect your agent to the Agensi MCP

      Copy the prompt and paste it into Claude, ChatGPT, Cursor or any agent that supports MCP. It sets up the connection for you. Manual setup

    2. 2

      Sign in to Agensi

      Your agent shows a sign-in link. Sign in and click Allow.

    3. 3

      Ask for what you need

      Your agent loads this skill and uses it on your task. It always asks before buying a skill.

    Reviews

    No reviews yet

    Be one of the first to try it. Every listed skill goes through the trust checks below.

    Security scanned

    Checked by our 8-point scan before listing

    Fresh listing

    Recently published to Agensi

    Money-back guarantee

    Doesn't do what its page promises? You get your money back.

    Trust & safety

    Security scan

    Security scan passed 10 days ago

    Permissions

    Read Files
    Write Files
    Listed10 days ago

    What's inside

    Frequently Asked Questions

    This skill analyzes your Bill of Materials (BOM) to identify over-specced components and suggests more affordable, functional alternatives to improve margins and bypass supply chain bottlenecks.

    The skill accepts standard CSV or Markdown exports from major ECAD software like Altium, KiCad, and Eagle, ensuring it fits directly into your existing engineering workflow.

    While the agent suggests alternatives based on functional specs and footprints, it does not perform physical signal integrity or thermal simulation; all suggested changes must be validated by a qualified engineer.

    Unlike generic prompts, this skill is programmed to provide at least two viable alternatives per item and specifically maps functional trade-offs, preventing the common issue of suggesting obsolete or incompatible parts.

    You receive the full agent skill logic designed for hardware optimization, a structured reporting template for alternative sourcing, and documentation on how to input your non-negotiable core requirements.

    The skill uses extensive historical data to flag components prone to volatility; however, because it does not have a live API link to distributors, we recommend a final real-time stock check before ordering.

    New in Business & Operations